To populate Alleyvale and turn it into a thriving town. Brad told stories of his hard life going from place to place before arriving here on the back of a guards van firmly fixed in place with a ziptie. Thanks to my brother David I have a few sheets of plywood so used that to great effect. Still to sort the windows with suitable acrylic sheet.
 |
| Fashioned up a bed from plywood covered with fabric from an old shirt, 2 pillows made from the same material. The dogs blanket donated a square to make a blanket. Everything hot glued into position, maybe a cat will use it as shelter? |
 |
| House in position, still to reshape the land and install a g gauge loop around the house, driveway, carport & fence. In the rear the first section of road cemented in place. |
 |
| Onto the next project, a small hotel with covered veranda, making good use of the jigsaw |
 |
| At this point I think a veranda might be nice, a place to sit and look at the passing trains |
 |
| Brad sizing the place up, showing off the "scrap wood" part of it. He does nothing but just stares out the window all day.. might get him a barbie, probably one that doesn't talk. |
 |
| The bottom floor, here will be the bar area. |
 |
| Everything somehow holding together long enough for a photo. Once the front balustrade is done the floor height wont be seen. |
 |
| Look at the appalling situation with Brad. He has most egregiously defaulted on his rent for five consecutive weeks. Furthermore, he has absolutely decimated the property; the sheer state of the place is a disgrace, and there is absolutely no question that his bond will be withheld in its entirety. He has finally been served with formal legal notice and has a mere three days to vacate the premises. We will naturally have to undertake a thorough deep-clean to return the property to an acceptable standard before we can place it back on the market. I intend to have the entire place repainted and plush new carpeting installed throughout. With any luck, our next tenant will be a properly tidy young lady. |
 |
| I found another 30cm male character named Tim "Buffer-Stop" Baker sitting inside the Da cab I completely forgot about, hes a bit more flexible and with more muscle than Brad. |
 |
| Buffer-Stop Tim's hands are able to grab the handrail! |
 |
| Given Tim's many years holding a job down as a driver and sick to death of sleeping in a chair for so many years I showed him the only house available in town until the hotels built. I told him about 10 minutes after paying the builder he disappeared without installing windows or working lights, so Tim offered half the asking rent until its fixed. Considering hes the only other bloke in town, I may have to accept his offer. He also wants to build a ride-on railway around the house, which is a little odd but at least hes not playing with dolls. |
 |
| Dad tried out the road with his rideon mower to check clearances, made it through fine but could be a bit wider for comfort. Concrete held up without cracking. |
 |
| I'm going to have to redo this area and widen it. |
 |
| A splash of white paint later |
 |
| Brad meets Tim in the hotel room, wood holding down the old reused carpet. If I used O gauge track & wheels under the peckett I think it would be close to 7.25" gauge in 1:6 scale? In my case i'm going to use G gauge track since I have it, good chance to use the tight radius stuff. G gauge track at 45mm in 1:6 scale works out at 7.5mm, so if I had N gauge track (9mm) with a nz120 locomotive it could roughly represent one of Tim's G gauge NZR locomotives. The G gauge Peckett representing a 1/6 scale model peckett somehow also works. |
 |
| Tim showing brad his battery electric 12" gauge? very scale peckett, apparently it's going to run around a house one day when hes more settled! Brad mentions hes once again homeless, but once the hotel is finished hes should have himself a room under the Winz Emergency Housing Special Needs Grant. This will at least give Brad short-term, temporary accommodation (such as motels or backpackers) for up to 7 nights at a time. Until then Brad has been helping the hotel build posing for photos and helping hold the carpet down and in exchange hes allowed to stay overnight.. as long as hes tidy. |
 |
| A bit later on and ol Buffer-Stop Tim shows us why they gave him the nickname Buffer-Stop. Earlier he pulled out a G gauge Db locomotive he purchased from a guy who lives in a green bus that drew it up on computer and somehow a microwave oven thermal printer 2 or 3 dee printer something produced it! He claimed he worked on the Db class of locomotive way back but his age doesn't quite match his story! The yarns continued into the night, I'm a little bit nervous about the amount of rubbish but i'm sure its fine |
 |
| A start on the balustrade glued into place and a lick of paint added |
 |
3d printer back up and running, now printing window frames & gingerbread trim. eventually settled on a top curved window frame so I could print vertical without support material
|
 |
A bit dark but the 2 windows are in place, the curved window stands out better
|
 |
Gingerbread trim glued in place, all window & door frames in place
|
